Select a mount for specs and install details. Use the Will It Fit? tool below to find which mount works for your vehicle. Email us if unsure.
Standard Mount +
- Mount Time15-25 minutes
- Height Added~5" off crossbar
- ToolsMini Ratchet or 4mm Allen + 10mm Nut Driver
- SecurityLocking Bolt upgrade available
- Bars >1.5" thickExtended Bolts required
- Bars <1.5" from roofShort Bolts required (4Runner, CRV)
Best For
- Most factory crossbars under 1.5" thick and 3.5" wide
- Most cost-effective mount option
Watch Out For
- Bars >1.5" thick need Extended Bolts
- Bars <1.5" from roof need Short Bolts
- Check hatch clearance before final tightening
My crossbars are thicker than 1.5". What do I need?
Extended Mounting Bolts (sold separately). These add 1" to the standard bolt length. Also required with any spacer kit.
My factory crossbars sit very close to the roof. What do I do?
If crossbars sit less than 1.5" above the roofline you need Short Bolts. Common on early Toyota 4Runner and Honda CRV.
Can I add a lock to the Standard Mount?
Yes. The Mount Lock Kit replaces standard hardware with tamper-proof locking bolts and a uniquely coded driver.
Can I mount both brackets on the rear half of the River Quiver?
Yes. Normal and acceptable for most SUVs with a rear hatch. Move mounts to the opposite mounting track and mount reel box up.
Low-Profile T-Track Mount +
- Mount Time~7 minutes
- Height Added<3" off crossbar
- T-Track Hardware18mm square included
- SecurityUnique key driver included
- ToolsMini Ratchet or 4mm Allen
Best For
- Crossbars with integrated T-tracks (Yakima, Thule, Rhino-Rack)
- Overland rooftop and bed racks
- Hanging below a rooftop tent on a bed rack
- Lowest possible mounting profile
Watch Out For
- Non-18mm platforms need hardware from rack manufacturer
- Install security caps only after all bolts are fully tightened
- Check reel box clearance
My rack uses a different T-track size. What do I do?
Contact your rack manufacturer for the correct hardware spec. Common non-standard platforms: Prinsu, Sherpa, CBI, 8020-style. Email us your rack brand and we can advise.
The security caps won't sit flush. What's wrong?
Security caps must go on after all bolts are fully tightened. Remove caps, tighten all bolts, then reinstall.
Can this mount be used to hang the River Quiver below a rooftop tent?
Yes. One of the best applications for this mount. The low-profile design minimizes footprint below the tent or rack.
Quick Release Mount +
- Mount Time~3 min after initial setup
- Height Added~4" off crossbar
- SecurityLock and key included
- ToolsMini Ratchet or 4mm Allen only
Best For
- Widest range of factory and aftermarket crossbars
- Frequent removal
- Oversized crossbars
- Anyone wanting a key-locking mount
Common Mistakes
- Not pivoting the mount before fitting
- Strap not loosened before fitting
- Forcing the latch
- Forgetting to re-tighten pivot bolt after positioning
My QR latch won't close. Step-by-step fix?
- Mount not pivoted. The latch must open fully before the strap can seat around the crossbar.
- Strap not loose enough. Loosen the adjustment bolt until the strap seats comfortably, then tighten gradually until the latch closes firmly.
Never force the latch.
What step is most commonly missed during QR installation?
Re-tightening the pivot bolt after final positioning. Once the strap is seated and the latch closes, re-tighten the pivot bolt to lock the mount angle.
I forgot to lock my mounts before driving. Is anything damaged?
Check all hardware immediately. If everything is tight and nothing shifted, you are likely fine. Always lock mounts before driving.
Truck Bed Mount +
- Mount Time~5 min after setup
- Height AddedVaries by bed rail height
- 2-Banger2 mounts included
- 4-Banger3 mounts + offset spacers
- DrillingNot required with factory rails or Ford BoxLink
- ToolsMini Ratchet or 4mm Allen
Best For
- Mid-size and full-size pickups with bed rails
- No-drill installs with factory cargo rails or Ford BoxLink
- Rods out of sight and out of the elements
Watch Out For
- Tailgate clearance
- 4-Banger requires all three mounts
- Drop-in liners with gaps
GM and Dodge Trucks
No factory-compatible rails. Options:
My tailgate hits the reel box. What do I do?
Shift the mounts forward until the tailgate closes fully. Confirm clearance before final tightening.
Why does the 4-Banger use three mounts?
The 4-Banger is wider and heavier. The third mount controls flex and distributes load evenly. Skipping it creates a flex point that wears hardware over time.
Will the mounting screws go through the bed panel?
No. Maximum plunge is ~1". Standard bed panels are significantly thicker. Do not over-torque.
Will it work under my tonneau cover?
Depends on cover type. You need clearance for the reel box lid to open. Email us with your cover model if unsure.
General Mounting Questions+
How do I know if my install is correct?
- Mounts fully seated with no movement
- All bolts firm, not over-cranked
- No gap at the coupler seam
- Reel box opens and closes cleanly
- Hatch or tailgate clears the reel box
- Vehicle height recorded
Drive a short distance and recheck all hardware. Repeat before trips and after rough terrain.
What is the minimum crossbar spacing?
- 4-Banger: 33" minimum
- 2-Banger: 28" minimum
- ShortCut: No strict minimum — must be fully supported by two crossbars
Reel box up or reel box down — does it matter?
No performance difference in any orientation. Choose whatever works best for your vehicle clearance and access preference.
There is a gap at my coupler seam. Is that okay?
No. A gap creates a catch point that can damage rod blanks. Disassemble, support both halves on a flat surface, start all bolts by hand, and tighten evenly. Never force a bolt that won't start by hand.
Can I leave my River Quiver on year-round?
Yes. In winter or coastal environments check hardware more frequently and rinse the extrusion interior at the start and end of each season.
Can I go through a car wash with my River Quiver mounted?
Hand washing is recommended. Touchless or brushless washes may be acceptable with adequate clearance. Brush washes should be avoided.
I have a Rhino-Rack Pioneer platform. What works?
A 2-Banger can often work with Standard or QR mounts on the horizontal cross supports. The 4-Banger is more difficult due to slat spacing. Email us your Pioneer configuration before ordering.
Can I mount a River Quiver on an overland or basket rack?
Generally yes with planning. Email us your rack brand and configuration.
Mounting Dimension Guide+
Use this diagram to understand crossbar spacing and mount placement relative to the coupler before installing.
- List
- Map